How to loosen stuck, rusted and seized nuts and bolts

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)
loading...Loading...

If you ask what is the single thing that is most affected by rust and corrosion, the unanimous answer would be nuts and bolts. Most of the time, the nuts become one with the accompanying bolt. They are so stuck and seized in place that it becomes difficult to even move them. Rusted equipment can cause serious harm to any product. Unless these are covered with rust-resistant sprays, they are at a risk of rusting and corroding. There are some particular conditions that fasten the rate of rusting such as a humid climate and too much exposure to moisture. While not all forms of rust are detectable visibly. They can cause harm to the equipment and can even lead to their malfunctioning.

Rust and corrosion in case of bolts and nuts can lead to the failure of the entire component. Therefore, it is important to address the issue of rust promptly before the damage is done.

Removing a Rusted Fastener

If the bolts and nuts are exposed to a humid weather or moisture for a long period of time, they will rust rather quickly. One component that is most affected by rust is fasteners present in automobile components and home appliances.

Moisture can lead to the degradation of the fasteners which makes the devices on the verge of a collapse. It is difficult to remove these stuck fasteners especially if the metal head or the threads are affected by rust. Rust makes it hard to grip the fasteners using a screwdriver or a wrench.

Removing rusted fasteners can be done in a number of ways. Here are the ones that are most commonly used and are most effective.

Lubrication:

If the fasteners are stuck in their place because of rust, making use of WD-40 Penetrant Spray is the ideal solution. If the rust has reached the threads of the fastener, then there is no better way to loosen it than using WD-40 penetrant spray. Apply it to the bolt and then tap it using a hammer. This will help WD-40 penetrant spray to penetrate the fitting and loosen the bolt so that it can removed easily.

Cutting:

If the fastener is so severely rusted that it cannot be salvaged, the only option left is to cut it out. This will make the fastener unusable but will help you get rid of it. You can use a clamp to get a good grip on the fastenerโ€™s head and twist it hard so it can be freed from its position.

Torching:

Another viable method to loosen rusted nuts and bolts is to use a heat torch on low or moderate heat. Heat will allow the rusted nuts and bolts to expand enough that they can be loosened. It is, however, important to be very careful with this method. Many lubricants applied to the nuts and bolts are flammable and can ignite if exposed to flame.

Tried and Tested Methods for Rust Removal

While it is possible to get rid of the rusted fastener and replace it with a new one, this option is not available in all the cases. There are many old machines and parts whose nuts and bolts cannot be replaced with new ones.

In such cases, you need to restore the nuts and bolts using rust removal techniques, which is a cost-effective method to keep the device functioning. Here are some common techniques used for rust removal.

Sanding:

Once you are done with removing a rusted fastener, you can rub it with steel wool or a sandpaper to scrap off the remaining rust. This is an inexpensive and a relatively simple method. It can be very time consuming and will also need a lubricant to make the fastener able to be used again.

Hydrogen Peroxide:

Applying hydrogen peroxide to the fasteners and letting it sit in for a while is also an effective method to remove rust from nuts and bolts. Hydrogen peroxide dissolves rust. Scouring it with a hard brush will help you get rid of all the rust left on the nuts and bolts. This is also an inexpensive method of treating rust but can leave residual rust spots behind.

Repainting:

Coating the nuts and screws with paint can also prevent them from rusting. Remove rust from the nuts and bolts before coating them in paint that keeps them safe from moisture, the leading cause of rust. A wax-based or oil-based coating can also help in preventing rust from building up on the nuts and screws again.

Rust Cleaner:

You can find a number of rust cleaners that can help in getting rid of rust from nuts and bolts. WD-40 penetrant spray not only helps in loosening the rusty and stuck nuts and bolts, but can also help in keeping them safe from getting rusted again in the future.

Getting rid of rust from nuts and screws and loosening the stuck ones can be an arduous task. If you are in search for the best lubricant to make the task easy for you, then nothing beats WD-40 penetrant spray. All you need to do it spray the rusted and seized nuts and bolts with it.

This will then work its magic in loosening them up. WD-40 Penetrant is a fast acting powerful and quickly penetrating spray that goes to the hard reaching areas and loosens the stuck and seized fixings.

It also helps in loosening the rusted moving parts and is water resistant. thus keeps moisture at bay keeping your nuts and bolts secure from future rusting and corrosion.

 

Related links

Sign up for exclusive news & offers!

© 2018 WD-40 Company